- Home/
- Comparison/
- Grader/
- Caterpillar 160M2 vs. John Deere 770A
Caterpillar 160M2 vs. John Deere 770A
20 reasons to buy Caterpillar 160M2:
Sizes
Front part clearance | 600 mm and 572 mm | 5 % more or 28 mm |
Operation
Front axle maximum operating weight | 6052.3 kg and 4123.6 kg | 32 % more or 1928.7 kg |
Rear axle maximum operating weight | 16530.7 kg and 11230 kg | 32 % more or 5300.7 kg |
Generator current strength | 150 amperes and 42 amperes | 72 % more or 108 amperes |
Fuel Capacity | 416.4 l. and 265 l. | 36 % more or 151.4 l. |
Oil system fluid volume | 29.9 l. and 18.9 l. | 37 % more or 11.0 l. |
Cooling system fluid volume | 56 l. and 26.5 l. | 53 % more or 29.5 l. |
Circular gearbox fluid volume | 6.8 l. and 3.8 l. | 44 % more or 3.0 l. |
Each tandem case fluid volume | 64 l. and 18.9 l. | 70 % more or 45.1 l. |
Front axle standard operating weight | 4236.1 kg and 3877.3 kg | 8 % more or 358.8 kg |
Rear axle standard operating weight | 13059.8 kg and 9848.4 kg | 25 % more or 3211.4 kg |
Motor
Torque measured at | 2100 rev / min and 1300 rev / min | 38 % more or 800 rev |
Effective speeds output 7-8 | 181.2 kW and 111.9 kW | 38 % more or 69.3 kW |
Effective drives torque 7-8 | 1355.8 Nm and 630.5 Nm | 53 % more or 725.3 Nm |
Gear box
Maximum forward speed | 46.7 km/h and 40.4 km/h | 13 % more or 6.3 km/h |
Maximum reverse gear | 36.9 km/h and 13.8 km/h | 63 % more or 23.1 km/h |
Reverse gears number | 6 and 4 | 33 % more or 2 |
Front Axle
Clearance | 600 mm and 572 mm | 5 % more or 28 mm |
Circle
Maximum radius outside left tyres | 2090 mm and 2280 mm | 8 % less or 190 mm |
Maximum lifting above ground level | 452 mm and 432 mm | 4 % more or 20 mm |
7 reasons to buy John Deere 770A:
Steerage
Turn radius | 6.7 m and 7.8 m | 14 % less or 1.1 m |
Operation
Hydraulic system fluid volume | 117 l. and 99.9 l. | 15 % more or 17.1 l. |
Motor
Power measured at | 2200 rev / min and 2100 rev / min | 5 % more or 100 rev |
Hydraulic system
Pump flow rate | 136.3 l/min and 210.1 l/min | 35 % less or 73.8 l/min |
Circle
Right maximum radius outside tyres | 2250 mm and 2278 mm | 1 % less or 28 mm |
Blade tilt front angle | 44 degrees and 40 degrees | 9 % more or 4 degrees |
Blade tilt rear angle | 10 degrees and 5 degrees | 50 % more or 5 degrees |
Neutral reasons:
Steerage
Left and right hinge connection | 20 degrees and 25 degrees |
Sizes
Wheelbase | 6126 mm and 5970 mm |
Dual axis wheelbase | 1523 mm and 1540 mm |
Blade base | 2557 mm and 2720 mm |
Height to cab upper part | 3287 mm and 3200 mm |
Dimensional length | 8898 mm and 8470 mm |
Between tyres width | 2581 mm and 2440 mm |
Operation
Overall standard operating weight | 17295.9 kg and 13725.7 kg |
Total maximum operating weight | 23947.4 kg and 15353.6 kg |
Operating voltage | 24 V and 24 V |
Motor
Manufacturer | Caterpillar and John Deere |
Model | C9.3 ACERT VHP and 6-466A |
Cylinders number | 6 and 6 |
Hydraulic system
Type of pump | variable displacement piston pump and Constant pressure system with locking in the middle position, with the piston pump of variable displacement volume |
Gear box
Transmission type | Powershift transmission with direct drive and powershift |
Forward gears number | 8 and 8 |
Front Axle
Wheel tilt | 18 degrees and 20 degrees |
General fluctuations | 32 degrees and 30 degrees |
Dump
Mouldboard height | 609.6 mm and 609.6 mm |
Mouldboard thickness | 22 mm and 22.4 mm |
Left lateral displacement | 510 mm and 683 mm |
Lateral right shift | 660 mm and 683 mm |
Mouldboard width | 4267.2 mm and 3657.6 mm |
Circle
Diameter | 1530 mm and 1500 mm |
Rotating | 360 degrees and 360 degrees |
Left shift | 695 mm and 851 mm |
Right shift | 728 mm and 813 mm |
Images
Sizes
1. Dimensional length | 8898 mm | 1. Dimensional length | 8470 mm |
2. Between tyres width | 2581 mm | 2. Between tyres width | 2440 mm |
3. Height to cab upper part | 3287 mm | 3. Height to cab upper part | 3200 mm |
4. Wheelbase | 6126 mm | 4. Wheelbase | 5970 mm |
6. Front part clearance | 600 mm | 6. Front part clearance | 572 mm |
7. Dual axis wheelbase | 1523 mm | 7. Dual axis wheelbase | 1540 mm |
8. Blade base | 2557 mm | 8. Blade base | 2720 mm |