- Home/
- Comparison/
- Grader/
- John Deere 770D vs. Fiat-Hitachi FG105
John Deere 770D vs. Fiat-Hitachi FG105
15 reasons to buy John Deere 770D:
Steerage
Turn radius | 7 m and 10 m | 30 % less or 3 m |
Sizes
Front part clearance | 638 mm and 635 mm | 0 % more or 3 mm |
Operation
Circular gearbox fluid volume | 5.7 l. and 2.8 l. | 51 % more or 2.9 l. |
Each tandem case fluid volume | 75.7 l. and 30.3 l. | 60 % more or 45.4 l. |
Generator current strength | 100 amperes and 45 amperes | 55 % more or 55 amperes |
Front axle maximum operating weight | 7185 kg and 4210 kg | 41 % more or 2975 kg |
Rear axle maximum operating weight | 14587 kg and 11390 kg | 22 % more or 3197 kg |
Fuel Capacity | 401.2 l. and 299 l. | 25 % more or 102.2 l. |
Cooling system fluid volume | 49.2 l. and 27 l. | 45 % more or 22.2 l. |
Motor
Maximum power | 160.3 kW and 147 kW | 8 % more or 13.3 kW |
Effective drives torque 7-8 | 1223 Nm and 753 Nm | 38 % more or 470 Nm |
Gear box
Forward gears number | 8 and 6 | 25 % more or 2 |
Reverse gears number | 8 and 3 | 62 % more or 5 |
Maximum reverse gear | 41.6 km/h and 27.4 km/h | 34 % more or 14.2 km/h |
Front Axle
Clearance | 638 mm and 635 mm | 0 % more or 3 mm |
13 reasons to buy Fiat-Hitachi FG105:
Operation
Hydraulic system fluid volume | 94.6 l. and 53 l. | 44 % more or 41.6 l. |
Transmission fluid volume | 25 l. and 22.7 l. | 9 % more or 2.3 l. |
Rear differential/final drive fluid volume | 42 l. and 36 l. | 14 % more or 6 l. |
Motor
Effective speeds output 5-6 | 147 kW and 138 kW | 6 % more or 9 kW |
Torque measured at | 1500 rev / min and 1000 rev / min | 33 % more or 500 rev |
Displacement | 8.3 l. and 8.1 l. | 2 % more or 0.2 l. |
Power measured at | 2300 rev / min and 2000 rev / min | 13 % more or 300 rev |
Hydraulic system
Pump flow rate | 163 l/min and 207 l/min | 21 % less or 44 l/min |
Gear box
Maximum forward speed | 42 km/h and 41.6 km/h | 1 % more or 0.4 km/h |
Circle
Maximum radius outside left tyres | 1759 mm and 2100 mm | 16 % less or 341 mm |
Right maximum radius outside tyres | 2057 mm and 2080 mm | 1 % less or 23 mm |
Maximum lifting above ground level | 622 mm and 470 mm | 24 % more or 152 mm |
Blade tilt rear angle | 27.5 degrees and 5 degrees | 82 % more or 22.5 degrees |
Neutral reasons:
Steerage
Left and right hinge connection | 22 degrees and 25 degrees |
Sizes
Height to cab upper part | 3180 mm and 3340 mm |
Dimensional length | 8804 mm and 8521 mm |
Between tyres width | 2510 mm and 2540 mm |
Wheelbase | 6120 mm and 1538 mm |
Blade base | 2568 mm and 2642 mm |
Dual axis wheelbase | 1540 mm and 5969 mm |
Operation
Tyre size | 14.00R24 Radial PR and 13X24(10PR) |
Operating voltage | 24 V and 24 V |
Total maximum operating weight | 21772 kg and 15600 kg |
Motor
Cylinders number | 6 and 6 |
Aspiration | Turbocharged engine with subsequent cooling of charging air by oncoming air flow and turbocharging |
Manufacturer | John Deere and Cummins |
Model | 6081H and 6 CT8.3 |
Hydraulic system
Overflow valve pressure | 18960.6 kPa and 2857 kPa |
Type of pump | variable displacement piston pump and fully oil-actuated, variable displacement piston pump |
Gear box
Transmission type | Powershift transmission with direct drive and powershift transmission |
Front Axle
Wheel tilt | 20 degrees and 17.5 degrees |
General fluctuations | 32 degrees and 19 degrees |
Dump
Mouldboard width | 3660 mm and 2762 mm |
Mouldboard height | 610 mm and 953 mm |
Left lateral displacement | 680 mm and 533 mm |
Lateral right shift | 680 mm and 685 mm |
Circle
Diameter | 1520 mm and 1753 mm |
Rotating | 360 degrees and 360 degrees |
Images
Sizes
7. Dual axis wheelbase | 1540 mm | 7. Dual axis wheelbase | 5969 mm |
8. Blade base | 2568 mm | 8. Blade base | 2642 mm |
1. Dimensional length | 8804 mm | 1. Dimensional length | 8521 mm |
2. Between tyres width | 2510 mm | 2. Between tyres width | 2540 mm |
3. Height to cab upper part | 3180 mm | 3. Height to cab upper part | 3340 mm |
4. Wheelbase | 6120 mm | 4. Wheelbase | 1538 mm |
6. Front part clearance | 638 mm | 6. Front part clearance | 635 mm |