- Home/
- Comparison/
- Grader/
- Terex TG190 vs. John Deere 872D
Terex TG190 vs. John Deere 872D
11 reasons to buy Terex TG190:
Sizes
Front part clearance | 591 mm and 587 mm | 1 % more or 4 mm |
Operation
Front axle standard operating weight | 5000 kg and 4613 kg | 8 % more or 387 kg |
Fuel Capacity | 480 l. and 401.2 l. | 16 % more or 78.8 l. |
Rear axle standard operating weight | 13700 kg and 11812 kg | 14 % more or 1888 kg |
Hydraulic system fluid volume | 170 l. and 53 l. | 69 % more or 117 l. |
Transmission fluid volume | 34 l. and 22.7 l. | 33 % more or 11.3 l. |
Circular gearbox fluid volume | 6 l. and 5.7 l. | 5 % more or 0.3 l. |
Hydraulic system
Pump flow rate | 99 l/min and 207 l/min | 52 % less or 108 l/min |
Front Axle
Clearance | 591 mm and 587 mm | 1 % more or 4 mm |
Circle
Maximum radius outside left tyres | 2220 mm and 2320 mm | 4 % less or 100 mm |
Maximum lifting above ground level | 470 mm and 437 mm | 7 % more or 33 mm |
13 reasons to buy John Deere 872D:
Steerage
Turn radius | 7.2 m and 7.5 m | 4 % less or 0.3 m |
Operation
Generator current strength | 100 amperes and 55 amperes | 45 % more or 45 amperes |
Cooling system fluid volume | 49.2 l. and 42 l. | 15 % more or 7.2 l. |
Each tandem case fluid volume | 75.7 l. and 42 l. | 45 % more or 33.7 l. |
Motor
Effective speeds output 5-6 | 182.7 kW and 138 kW | 24 % more or 44.7 kW |
Maximum power | 182.7 kW and 138 kW | 24 % more or 44.7 kW |
Displacement | 8.1 l. and 6 l. | 26 % more or 2.1 l. |
Gear box
Reverse gears number | 8 and 3 | 62 % more or 5 |
Maximum forward speed | 41.1 km/h and 40 km/h | 3 % more or 1.1 km/h |
Forward gears number | 8 and 6 | 25 % more or 2 |
Maximum reverse gear | 41.1 km/h and 19.4 km/h | 53 % more or 21.7 km/h |
Dump
Blade pulling at maximum weight | 19849 kg and 9835.2 kg | 50 % more or 10013.8 kg |
Circle
Right maximum radius outside tyres | 2310 mm and 3180 mm | 27 % less or 870 mm |
Neutral reasons:
Steerage
Left and right hinge connection | 45 degrees and 22 degrees |
Sizes
Height to cab upper part | 3300 mm and 3180 mm |
Dimensional length | 10266 mm and 8804 mm |
Between tyres width | 2490 mm and 2640 mm |
Wheelbase | 6136 mm and 6120 mm |
Blade base | 2638 mm and 2533 mm |
Dual axis wheelbase | 1542 mm and 1540 mm |
Operation
Overall standard operating weight | 18700 kg and 16421 kg |
Tyre size | 14.00 -24TG and 17.5R25 Radial PR |
Operating voltage | 24 V and 24 V |
Motor
Aspiration | turbocharging and Turbocharged engine with subsequent cooling of charging air by oncoming air flow |
Manufacturer | Cummins and John Deere |
Power measured at | 2000 rev / min and 2000 rev / min |
Cylinders number | 6 and 6 |
Hydraulic system
Overflow valve pressure | 18400 kPa and 18960.6 kPa |
Type of pump | axial piston pump and variable displacement piston pump |
Gear box
Transmission type | powershift transmission with torque converter and Powershift transmission with direct drive |
Front Axle
Wheel tilt | 17 degrees and 20 degrees |
General fluctuations | 15 degrees and 32 degrees |
Dump
Mouldboard width | 3660 mm and 4300 mm |
Mouldboard height | 630 mm and 686 mm |
Mouldboard thickness | 20 mm and 25 mm |
Left lateral displacement | 1250 mm and 680 mm |
Lateral right shift | 1250 mm and 680 mm |
Circle
Diameter | 1510 mm and 1520 mm |
Images
Sizes
1. Dimensional length | 10266 mm | 1. Dimensional length | 8804 mm |
2. Between tyres width | 2490 mm | 2. Between tyres width | 2640 mm |
3. Height to cab upper part | 3300 mm | 3. Height to cab upper part | 3180 mm |
4. Wheelbase | 6136 mm | 4. Wheelbase | 6120 mm |
6. Front part clearance | 591 mm | 6. Front part clearance | 587 mm |
7. Dual axis wheelbase | 1542 mm | 7. Dual axis wheelbase | 1540 mm |
8. Blade base | 2638 mm | 8. Blade base | 2533 mm |