- Home/
- Specifications/
- Grader/
- Volvo/
- G930
Construction Machinery. Grader Volvo G930
Steerage
| Left and right hinge connection | 50 degrees |
| Turn radius | 7265 m |
Sizes
| Height to cab upper part | 3225 mm |
| Dimensional length | 8930 mm |
| Between tyres width | 2537 mm |
| Wheelbase | 6280 mm |
| Blade base | 2675 mm |
| Front part clearance | 610 mm |
Operation
| Rear axle maximum operating weight | 14240 kg |
| Total maximum operating weight | 19280 kg |
| Fuel Capacity | 348 l. |
| Oil system fluid volume | 21.5 l. |
| Cooling system fluid volume | 31 l. |
| Hydraulic system fluid volume | 91 l. |
| Transmission fluid volume | 61 l. |
| Each tandem case fluid volume | 100 l. |
| Tyre size | 14:00 x 24, G-2 |
| Operating voltage | 24 V |
| Generator current strength | 80 amperes |
| Front axle standard operating weight | 4700 kg |
| Rear axle standard operating weight | 11100 kg |
| Overall standard operating weight | 15800 kg |
| Front axle maximum operating weight | 7570 kg |
Motor
| Manufacturer | Volvo |
| Model | D7EGCE3 |
| Power measured at | 1800 rev / min |
| Torque measured at | 1550 rev / min |
| Cylinders number | 6 |
| Effective speeds output 7-8 | 152.1 kW |
| Maximum power | 152.1 kW |
| Effective drives torque 7-8 | 928 Nm |
| Displacement | 7.2 l. |
| Aspiration | Turbocharging with subsequent air cooling (by a cooling radiator) |
Hydraulic system
| Type of pump | axial piston pump |
| Pump flow rate | 208 l/min |
| Overflow valve pressure | 207 kPa |
Gear box
| Transmission type | HTE 840, Sequential direct drive gearbox with shifting under load Volvo |
| Forward gears number | 8 |
| Reverse gears number | 4 |
| Maximum forward speed | 45.4 km/h |
| Maximum reverse gear | 32 km/h |
Front Axle
| Wheel tilt | 18 degrees |
| General fluctuations | 16 degrees |
| Clearance | 610 mm |
Dump
| Left lateral displacement | 673 mm |
| Lateral right shift | 673 mm |
| Blade pulling at maximum weight | 12816 kg |
| Lowered blade pressure | 8188 kg |
| Mouldboard width | 3657.6 mm |
| Mouldboard height | 635 mm |
| Mouldboard thickness | 22 mm |
| Maximum cutting depth | 790 mm |
Circle
| Diameter | 1626 mm |
| Rotating | 360 degrees |
| Left shift | 775 mm |
| Right shift | 749 mm |
| Maximum radius outside left tyres | 2020 mm |
| Right maximum radius outside tyres | 2010 mm |
| Maximum lifting above ground level | 492 mm |
| Blade tilt front angle | 47 degrees |
| Blade tilt rear angle | 5 degrees |
Images
Sizes
| 1. Dimensional length | 8930 mm |
| 2. Between tyres width | 2537 mm |
| 3. Height to cab upper part | 3225 mm |
| 4. Wheelbase | 6280 mm |
| 6. Front part clearance | 610 mm |
| 8. Blade base | 2675 mm |