vs.

      John Deere 670C vs. Komatsu GD675-3

      9 reasons to buy John Deere 670C:

      Steerage

      Turn radius 6.7 m and 6.9 m 3 % less or 0.2 m

      Operation

      Cooling system fluid volume 42 l. and 39.5 l. 6 % more or 2.5 l.
      Hydraulic system fluid volume 59 l. and 45 l. 24 % more or 14 l.
      Fuel Capacity 403 l. and 340 l. 16 % more or 63 l.

      Motor

      Power measured at 2000 rev / min and 1900 rev / min 5 % more or 100 rev

      Hydraulic system

      Pump flow rate 173 l/min and 194 l/min 11 % less or 21 l/min

      Gear box

      Reverse gears number 8 and 4 50 % more or 4
      Maximum reverse gear 40.2 km/h and 38.3 km/h 5 % more or 1.9 km/h

      Circle

      Blade tilt front angle 49 degrees and 40 degrees 18 % more or 9 degrees

      16 reasons to buy Komatsu GD675-3:

      Operation

      Circular gearbox fluid volume 5 l. and 3.8 l. 24 % more or 1.2 l.
      Each tandem case fluid volume 83 l. and 75 l. 10 % more or 8 l.
      Transmission fluid volume 45 l. and 38 l. 16 % more or 7 l.
      Generator current strength 90 amperes and 55 amperes 39 % more or 35 amperes
      Front axle standard operating weight 4300 kg and 3919 kg 9 % more or 381 kg
      Rear axle standard operating weight 11510 kg and 9913 kg 14 % more or 1597 kg

      Motor

      Maximum power 149 kW and 104.4 kW 30 % more or 44.6 kW
      Torque measured at 1400 rev / min and 1000 rev / min 29 % more or 400 rev
      Effective speeds output 7-8 149 kW and 104.4 kW 30 % more or 44.6 kW
      Effective drives torque 7-8 975 Nm and 672.5 Nm 31 % more or 302.5 Nm
      Displacement 8.3 l. and 6.8 l. 18 % more or 1.5 l.

      Gear box

      Maximum forward speed 42.2 km/h and 40.2 km/h 5 % more or 2.0 km/h

      Front Axle

      Clearance 630 mm and 610 mm 3 % more or 20 mm

      Circle

      Maximum radius outside left tyres 2000 mm and 2160 mm 7 % less or 160 mm
      Right maximum radius outside tyres 2000 mm and 2110 mm 5 % less or 110 mm
      Maximum lifting above ground level 505 mm and 444 mm 12 % more or 61 mm

      Neutral reasons:

      Steerage

      Left and right hinge connection 25 degrees and 23 degrees

      Sizes

      Height to cab upper part 3100 mm and 3120 mm
      Dimensional length 8580 mm and 9865 mm
      Between tyres width 2490 mm and 2550 mm
      Wheelbase 5970 mm and 6070 mm
      Blade base 2670 mm and 2600 mm
      Dual axis wheelbase 1540 mm and 1535 mm

      Operation

      Tyre size 13.00-24 and Low-pressure, without inner tube, 17.5R25
      Operating voltage 24 V and 24 V
      Overall standard operating weight 13832 kg and 15810 kg

      Motor

      Cylinders number 6 and 6
      Model 6068H and SAA6D114E-3
      Aspiration Turbocharging with subsequent air cooling (by a cooling radiator) and Turbocharged engine with subsequent cooling of charging air by oncoming air flow
      Manufacturer John Deere and Komatsu

      Hydraulic system

      Overflow valve pressure 17581.6 kPa and 20600 kPa
      Type of pump variable displacement with locking in the middle position and Hydraulic system of Closed Center Load Sensing System (CLSS)

      Gear box

      Transmission type powershift and powershift transmission
      Forward gears number 8 and 8

      Front Axle

      Wheel tilt 20 degrees and 20 degrees
      General fluctuations 32 degrees and 32 degrees

      Dump

      Mouldboard width 3.7 mm and 3710 mm
      Mouldboard height 610 mm and 660 mm
      Mouldboard thickness 22 mm and 25 mm
      Left lateral displacement 683 mm and 820 mm
      Lateral right shift 683 mm and 820 mm

      Circle

      Blade tilt rear angle 5 degrees and 5 degrees
      Diameter 1520 mm and 1530 mm
      Rotating 360 degrees and 360 degrees
      Left shift 787 mm and 625 mm
      Right shift 724 mm and 625 mm

      Images

      Sizes

      1. Dimensional length 8580 mm 1. Dimensional length 9865 mm
      2. Between tyres width 2490 mm 2. Between tyres width 2550 mm
      3. Height to cab upper part 3100 mm 3. Height to cab upper part 3120 mm
      4. Wheelbase 5970 mm 4. Wheelbase 6070 mm
      7. Dual axis wheelbase 1540 mm 7. Dual axis wheelbase 1535 mm
      8. Blade base 2670 mm 8. Blade base 2600 mm