vs.

      John Deere 872D vs. Komatsu GD675-3

      20 reasons to buy John Deere 872D:

      Operation

      Fuel Capacity 401.2 l. and 340 l. 15 % more or 61.2 l.
      Cooling system fluid volume 49.2 l. and 39.5 l. 20 % more or 9.7 l.
      Hydraulic system fluid volume 53 l. and 45 l. 15 % more or 8 l.
      Circular gearbox fluid volume 5.7 l. and 5 l. 12 % more or 0.7 l.
      Generator current strength 100 amperes and 90 amperes 10 % more or 10 amperes
      Front axle standard operating weight 4613 kg and 4300 kg 7 % more or 313 kg
      Rear axle standard operating weight 11812 kg and 11510 kg 3 % more or 302 kg

      Motor

      Effective speeds output 3-4 172 kW and 149 kW 13 % more or 23 kW
      Effective speeds output 1-2 153 kW and 134 kW 12 % more or 19 kW
      Power measured at 2000 rev / min and 1900 rev / min 5 % more or 100 rev
      Effective speeds output 5-6 182.7 kW and 149 kW 18 % more or 33.7 kW
      Effective speeds output 7-8 175.2 kW and 149 kW 15 % more or 26.2 kW
      Maximum power 182.7 kW and 149 kW 18 % more or 33.7 kW
      Effective drives torque 1-2 1075 Nm and 830 Nm 23 % more or 245 Nm
      Effective drives torque 3-4 1132 Nm and 975 Nm 14 % more or 157 Nm
      Effective drives torque 5-6 1182 Nm and 975 Nm 18 % more or 207 Nm
      Effective drives torque 7-8 1277 Nm and 975 Nm 24 % more or 302 Nm

      Gear box

      Maximum reverse gear 41.1 km/h and 38.3 km/h 7 % more or 2.8 km/h
      Reverse gears number 8 and 4 50 % more or 4

      Circle

      Blade tilt front angle 42 degrees and 40 degrees 5 % more or 2 degrees

      11 reasons to buy Komatsu GD675-3:

      Steerage

      Turn radius 6.9 m and 7.2 m 4 % less or 0.3 m

      Operation

      Transmission fluid volume 45 l. and 22.7 l. 50 % more or 22.3 l.
      Each tandem case fluid volume 83 l. and 75.7 l. 9 % more or 7.3 l.

      Motor

      Torque measured at 1400 rev / min and 1000 rev / min 29 % more or 400 rev
      Displacement 8.3 l. and 8.1 l. 2 % more or 0.2 l.

      Hydraulic system

      Pump flow rate 194 l/min and 207 l/min 6 % less or 13 l/min

      Gear box

      Maximum forward speed 42.2 km/h and 41.1 km/h 3 % more or 1.1 km/h

      Front Axle

      Clearance 630 mm and 587 mm 7 % more or 43 mm

      Circle

      Maximum radius outside left tyres 2000 mm and 2320 mm 14 % less or 320 mm
      Right maximum radius outside tyres 2000 mm and 2310 mm 13 % less or 310 mm
      Maximum lifting above ground level 505 mm and 437 mm 13 % more or 68 mm

      Neutral reasons:

      Steerage

      Left and right hinge connection 22 degrees and 23 degrees

      Sizes

      Height to cab upper part 3180 mm and 3120 mm
      Dimensional length 8804 mm and 9865 mm
      Between tyres width 2640 mm and 2550 mm
      Wheelbase 6120 mm and 6070 mm
      Blade base 2533 mm and 2600 mm
      Dual axis wheelbase 1540 mm and 1535 mm

      Operation

      Overall standard operating weight 16421 kg and 15810 kg
      Tyre size 17.5R25 Radial PR and Low-pressure, without inner tube, 17.5R25
      Operating voltage 24 V and 24 V

      Motor

      Cylinders number 6 and 6
      Aspiration Turbocharged engine with subsequent cooling of charging air by oncoming air flow and Turbocharged engine with subsequent cooling of charging air by oncoming air flow
      Manufacturer John Deere and Komatsu
      Model 6081H and SAA6D114E-3

      Hydraulic system

      Type of pump variable displacement piston pump and Hydraulic system of Closed Center Load Sensing System (CLSS)
      Overflow valve pressure 18960.6 kPa and 20600 kPa

      Gear box

      Transmission type Powershift transmission with direct drive and powershift transmission
      Forward gears number 8 and 8

      Front Axle

      Wheel tilt 20 degrees and 20 degrees
      General fluctuations 32 degrees and 32 degrees

      Dump

      Mouldboard width 4300 mm and 3710 mm
      Mouldboard height 686 mm and 660 mm
      Mouldboard thickness 25 mm and 25 mm
      Left lateral displacement 680 mm and 820 mm
      Lateral right shift 680 mm and 820 mm

      Circle

      Right shift 724 mm and 625 mm
      Left shift 787 mm and 625 mm
      Blade tilt rear angle 5 degrees and 5 degrees
      Diameter 1520 mm and 1530 mm
      Rotating 360 degrees and 360 degrees

      Images

      Sizes

      3. Height to cab upper part 3180 mm 3. Height to cab upper part 3120 mm
      4. Wheelbase 6120 mm 4. Wheelbase 6070 mm
      7. Dual axis wheelbase 1540 mm 7. Dual axis wheelbase 1535 mm
      8. Blade base 2533 mm 8. Blade base 2600 mm
      1. Dimensional length 8804 mm 1. Dimensional length 9865 mm
      2. Between tyres width 2640 mm 2. Between tyres width 2550 mm