- Home/
- Comparison/
- Grader/
- New Holland F170 vs. Komatsu GD555-3
New Holland F170 vs. Komatsu GD555-3
9 reasons to buy New Holland F170:
Operation
Hydraulic system fluid volume | 95 l. and 85 l. | 11 % more or 10 l. |
Oil system fluid volume | 19 l. and 14.4 l. | 24 % more or 4.6 l. |
Motor
Displacement | 8.3 l. and 5.9 l. | 29 % more or 2.4 l. |
Power measured at | 2200 rev / min and 2000 rev / min | 9 % more or 200 rev |
Hydraulic system
Pump flow rate | 183 l/min and 204.4 l/min | 10 % less or 21.4 l/min |
Gear box
Maximum forward speed | 43 km/h and 42.9 km/h | 0 % more or 0.1 km/h |
Front Axle
Clearance | 622 mm and 610 mm | 2 % more or 12 mm |
Circle
Maximum radius outside left tyres | 1735 mm and 2000 mm | 13 % less or 265 mm |
Right maximum radius outside tyres | 1895 mm and 2000 mm | 5 % less or 105 mm |
10 reasons to buy Komatsu GD555-3:
Steerage
Turn radius | 6.8 m and 7.3 m | 7 % less or 0.5 m |
Operation
Cooling system fluid volume | 42 l. and 40 l. | 5 % more or 2 l. |
Each tandem case fluid volume | 83 l. and 29 l. | 65 % more or 54 l. |
Transmission fluid volume | 45 l. and 19 l. | 58 % more or 26 l. |
Circular gearbox fluid volume | 5 l. and 2.8 l. | 44 % more or 2.2 l. |
Generator current strength | 90 amperes and 70 amperes | 22 % more or 20 amperes |
Motor
Effective drives torque 7-8 | 729.4 Nm and 230.5 Nm | 68 % more or 498.9 Nm |
Gear box
Maximum reverse gear | 39.1 km/h and 28.5 km/h | 27 % more or 10.6 km/h |
Dump
Maximum cutting depth | 835 mm and 712 mm | 15 % more or 123 mm |
Circle
Maximum lifting above ground level | 485 mm and 444 mm | 8 % more or 41 mm |
Neutral reasons:
Steerage
Left and right hinge connection | 25 degrees and 23 degrees |
Sizes
Between tyres width | 2510 mm and 2525 mm |
Blade base | 2562 mm and 2500 mm |
Wheelbase | 6219 mm and 5850 mm |
Dual axis wheelbase | 1594 mm and 1535 mm |
Height to cab upper part | 3340 mm and 3100 mm |
Dimensional length | 8521 mm and 9390 mm |
Operation
Tyre size | 13.00 x 24 (12PR) and Low-pressure, without inner tube, 14.00 X 24, 12 layers - G2 |
Operating voltage | 24 V and 24 V |
Fuel Capacity | 340 l. and 340 l. |
Motor
Manufacturer | Cummins and Komatsu |
Model | 6 CTAA 8.3 2 level and SAA6D102E-2 |
Aspiration | turbocharging and turbocharging and cooling at the outlet |
Cylinders number | 6 and 6 |
Hydraulic system
Overflow valve pressure | 17900 kPa and 20684.3 kPa |
Type of pump | full hydraulic system with load sensing and Hydraulic system of Closed Center Load Sensing System (CLSS) |
Gear box
Forward gears number | 8 and 8 |
Reverse gears number | 4 and 4 |
Transmission type | Powershift transmission with direct drive and powershift transmission |
Front Axle
Wheel tilt | 18 degrees and 20 degrees |
General fluctuations | 19 degrees and 32 degrees |
Dump
Mouldboard thickness | 22 mm and 22 mm |
Mouldboard height | 671 mm and 660 mm |
Left lateral displacement | 533 mm and 820 mm |
Lateral right shift | 686 mm and 820 mm |
Mouldboard width | 3962 mm and 3710 mm |
Circle
Diameter | 1753 mm and 1529.1 mm |
Rotating | 360 degrees and 360 degrees |
Blade tilt front angle | 40 degrees and 40 degrees |
Blade tilt rear angle | 5 degrees and 5 degrees |
Images
Sizes
1. Dimensional length | 8521 mm | 1. Dimensional length | 9390 mm |
2. Between tyres width | 2510 mm | 2. Between tyres width | 2525 mm |
3. Height to cab upper part | 3340 mm | 3. Height to cab upper part | 3100 mm |
4. Wheelbase | 6219 mm | 4. Wheelbase | 5850 mm |
7. Dual axis wheelbase | 1594 mm | 7. Dual axis wheelbase | 1535 mm |
8. Blade base | 2562 mm | 8. Blade base | 2500 mm |