vs.

      New Holland F200 vs. Dressta RD200C

      7 reasons to buy New Holland F200:

      Steerage

      Turn radius 7.3 m and 7500 m 100 % less or 7492.7 m

      Operation

      Rear differential/final drive fluid volume 25 l. and 7.5 l. 70 % more or 17.5 l.

      Motor

      Displacement 8.3 l. and 6.7 l. 19 % more or 1.6 l.

      Gear box

      Reverse gears number 4 and 3 25 % more or 1
      Forward gears number 8 and 6 25 % more or 2

      Front Axle

      Clearance 622 mm and 550 mm 12 % more or 72 mm

      Dump

      Maximum cutting depth 712 mm and 350 mm 51 % more or 362 mm

      10 reasons to buy Dressta RD200C:

      Operation

      Hydraulic system fluid volume 130 l. and 95.6 l. 26 % more or 34.4 l.
      Transmission fluid volume 35 l. and 22 l. 37 % more or 13 l.
      Each tandem case fluid volume 30 l. and 23 l. 23 % more or 7 l.
      Fuel Capacity 380 l. and 341 l. 10 % more or 39 l.
      Generator current strength 75 amperes and 70 amperes 7 % more or 5 amperes

      Motor

      Power measured at 2400 rev / min and 2200 rev / min 8 % more or 200 rev

      Hydraulic system

      Pump flow rate 80 l/min and 186 l/min 57 % less or 106 l/min

      Gear box

      Maximum forward speed 44.7 km/h and 43 km/h 4 % more or 1.7 km/h
      Maximum reverse gear 31.4 km/h and 30.6 km/h 3 % more or 0.8 km/h

      Circle

      Maximum lifting above ground level 500 mm and 445 mm 11 % more or 55 mm

      Neutral reasons:

      Steerage

      Left and right hinge connection 25 degrees and 25 degrees

      Sizes

      Height to cab upper part 3340 mm and 3300 mm
      Dimensional length 8555 mm and 9540 mm
      Between tyres width 2650 mm and 2500 mm
      Wheelbase 6219 mm and 7300 mm
      Blade base 2562 mm and 3050 mm
      Dual axis wheelbase 1602 mm and 1540 mm

      Operation

      Tyre size 14.00 x 24 (10PR) and 14.00 - 24 G-2 16PR
      Operating voltage 24 V and 24 V
      Cooling system fluid volume 40 l. and 40 l.

      Motor

      Manufacturer Cummins and Cummins
      Model 6 CTAA 8.3 2 level and QSB 6.7
      Cylinders number 6 and 6
      Aspiration turbocharging and turbocharging and CAC

      Hydraulic system

      Type of pump full hydraulic system with load sensing and axial piston pump
      Overflow valve pressure 17900 kPa and 14000 kPa

      Gear box

      Transmission type Powershift transmission with direct drive and powershift transmission

      Front Axle

      Wheel tilt 18 degrees and 22 degrees
      General fluctuations 19 degrees and 40 degrees

      Dump

      Mouldboard width 4267 mm and 3660 mm
      Mouldboard height 671 mm and 670 mm
      Mouldboard thickness 22 mm and 22 mm
      Left lateral displacement 533 mm and 800 mm
      Lateral right shift 686 mm and 800 mm

      Circle

      Diameter 1753 mm and 1350 mm
      Rotating 360 degrees and 360 degrees

      Images

      Sizes

      1. Dimensional length 8555 mm 1. Dimensional length 9540 mm
      2. Between tyres width 2650 mm 2. Between tyres width 2500 mm
      3. Height to cab upper part 3340 mm 3. Height to cab upper part 3300 mm
      4. Wheelbase 6219 mm 4. Wheelbase 7300 mm
      7. Dual axis wheelbase 1602 mm 7. Dual axis wheelbase 1540 mm
      8. Blade base 2562 mm 8. Blade base 3050 mm