vs.

      Volvo G740 VHP vs. John Deere 770CH

      16 reasons to buy Volvo G740 VHP:

      Operation

      Each tandem case fluid volume 100 l. and 75 l. 25 % more or 25 l.
      Generator current strength 75 amperes and 55 amperes 27 % more or 20 amperes
      Cooling system fluid volume 50 l. and 45.4 l. 9 % more or 4.6 l.
      Front axle standard operating weight 4851 kg and 3987.1 kg 18 % more or 863.9 kg
      Hydraulic system fluid volume 90 l. and 59 l. 34 % more or 31 l.
      Rear axle standard operating weight 11302 kg and 10301.1 kg 9 % more or 1000.9 kg

      Motor

      Power measured at 2100 rev / min and 1900 rev / min 10 % more or 200 rev
      Torque measured at 1300 rev / min and 900 rev / min 31 % more or 400 rev
      Effective speeds output 7-8 175.2 kW and 152.9 kW 13 % more or 22.3 kW
      Maximum power 175.2 kW and 152.9 kW 13 % more or 22.3 kW
      Effective drives torque 7-8 1145.7 Nm and 924.7 Nm 19 % more or 221.0 Nm
      Displacement 10.8 l. and 8.1 l. 25 % more or 2.7 l.

      Hydraulic system

      Pump flow rate 183 l/min and 207.1 l/min 12 % less or 24.1 l/min

      Gear box

      Maximum forward speed 43.8 km/h and 41.5 km/h 5 % more or 2.3 km/h

      Circle

      Maximum radius outside left tyres 2019.3 mm and 2160 mm 7 % less or 140.7 mm
      Right maximum radius outside tyres 2006.6 mm and 2110 mm 5 % less or 103.4 mm

      9 reasons to buy John Deere 770CH:

      Operation

      Rear differential/final drive fluid volume 36 l. and 23 l. 36 % more or 13 l.
      Fuel Capacity 401.3 l. and 378.5 l. 6 % more or 22.8 l.

      Gear box

      Reverse gears number 8 and 4 50 % more or 4
      Maximum reverse gear 41.5 km/h and 31.4 km/h 24 % more or 10.1 km/h

      Front Axle

      Clearance 638 mm and 610 mm 4 % more or 28 mm

      Dump

      Blade pulling at maximum weight 12696.1 kg and 10171.4 kg 20 % more or 2524.7 kg

      Circle

      Maximum lifting above ground level 470 mm and 436.9 mm 7 % more or 33.1 mm
      Blade tilt front angle 49 degrees and 44 degrees 10 % more or 5 degrees
      Blade tilt rear angle 5 degrees and 2.5 degrees 50 % more or 2.5 degrees

      Neutral reasons:

      Steerage

      Left and right hinge connection 22 degrees and 25 degrees

      Sizes

      Height to cab upper part 3099 mm and 3120 mm
      Dimensional length 8636 mm and 8610 mm
      Between tyres width 2540 mm and 2510 mm
      Wheelbase 6248 mm and 5970 mm
      Blade base 2718 mm and 2670 mm

      Operation

      Overall standard operating weight 16153 kg and 14288.2 kg
      Tyre size 14.00 x 24, G-2 and 14.00-24
      Operating voltage 24 V and 24 V
      Transmission fluid volume 38 l. and 38 l.

      Motor

      Aspiration turbocharging and Turbocharging with subsequent air cooling (by a cooling radiator)
      Manufacturer Cummins and John Deere
      Model M11 and 6081H

      Hydraulic system

      Overflow valve pressure 17236.9 kPa and 17581.6 kPa
      Type of pump hydraulic system with load sensing and variable displacement with locking in the middle position

      Gear box

      Forward gears number 8 and 8
      Transmission type powershift transmission and powershift

      Front Axle

      Wheel tilt 18 degrees and 20 degrees
      General fluctuations 16 degrees and 32 degrees

      Dump

      Mouldboard width 4572 mm and 3657.6 mm
      Mouldboard height 736.6 mm and 609.6 mm
      Mouldboard thickness 25.4 mm and 22.4 mm
      Left lateral displacement 673.1 mm and 683 mm
      Lateral right shift 673.1 mm and 683 mm

      Circle

      Left shift 774.7 mm and 787 mm
      Right shift 749.3 mm and 724 mm
      Diameter 1683 mm and 1520 mm
      Rotating 360 degrees and 360 degrees

      Images

      Sizes

      8. Blade base 2718 mm 8. Blade base 2670 mm
      1. Dimensional length 8636 mm 1. Dimensional length 8610 mm
      2. Between tyres width 2540 mm 2. Between tyres width 2510 mm
      3. Height to cab upper part 3099 mm 3. Height to cab upper part 3120 mm
      4. Wheelbase 6248 mm 4. Wheelbase 5970 mm