vs.

      Volvo G946 vs. John Deere 770A

      21 reasons to buy Volvo G946:

      Sizes

      Front part clearance 610 mm and 572 mm 6 % more or 38 mm

      Operation

      Generator current strength 80 amperes and 42 amperes 47 % more or 38 amperes
      Front axle maximum operating weight 7570 kg and 4123.6 kg 46 % more or 3446.4 kg
      Rear axle maximum operating weight 14240 kg and 11230 kg 21 % more or 3010 kg
      Front axle standard operating weight 5000 kg and 3877.3 kg 22 % more or 1122.7 kg
      Rear axle standard operating weight 12300 kg and 9848.4 kg 20 % more or 2451.6 kg
      Fuel Capacity 404 l. and 265 l. 34 % more or 139 l.
      Oil system fluid volume 21.5 l. and 18.9 l. 12 % more or 2.6 l.
      Cooling system fluid volume 34 l. and 26.5 l. 22 % more or 7.5 l.
      Hydraulic system fluid volume 144 l. and 117 l. 19 % more or 27 l.
      Each tandem case fluid volume 100 l. and 18.9 l. 81 % more or 81.1 l.

      Motor

      Torque measured at 1500 rev / min and 1300 rev / min 13 % more or 200 rev
      Effective speeds output 7-8 167.8 kW and 111.9 kW 33 % more or 55.9 kW
      Maximum power 167.8 kW and 111.9 kW 33 % more or 55.9 kW
      Effective drives torque 7-8 1023 Nm and 630.5 Nm 38 % more or 392.5 Nm

      Gear box

      Maximum forward speed 45.4 km/h and 40.4 km/h 11 % more or 5.0 km/h
      Maximum reverse gear 32 km/h and 13.8 km/h 57 % more or 18.2 km/h

      Front Axle

      Clearance 610 mm and 572 mm 6 % more or 38 mm

      Circle

      Maximum radius outside left tyres 2020 mm and 2280 mm 11 % less or 260 mm
      Right maximum radius outside tyres 2010 mm and 2250 mm 11 % less or 240 mm
      Blade tilt front angle 45 degrees and 44 degrees 2 % more or 1 degrees

      5 reasons to buy John Deere 770A:

      Steerage

      Turn radius 6.7 m and 7265 m 100 % less or 7258.3 m

      Motor

      Displacement 7.6 l. and 7.2 l. 5 % more or 0.4 l.
      Power measured at 2200 rev / min and 1800 rev / min 18 % more or 400 rev

      Hydraulic system

      Pump flow rate 136.3 l/min and 208 l/min 34 % less or 71.7 l/min

      Circle

      Blade tilt rear angle 10 degrees and 6 degrees 40 % more or 4 degrees

      Neutral reasons:

      Steerage

      Left and right hinge connection 23 degrees and 25 degrees

      Sizes

      Wheelbase 6280 mm and 5970 mm
      Blade base 2650 mm and 2720 mm
      Height to cab upper part 3225 mm and 3200 mm
      Dimensional length 9150 mm and 8470 mm
      Between tyres width 2537 mm and 2440 mm

      Operation

      Overall standard operating weight 17300 kg and 13725.7 kg
      Total maximum operating weight 21770 kg and 15353.6 kg
      Tyre size 14:00 x 24, G-2 and 14.00-25
      Operating voltage 24 V and 24 V

      Motor

      Aspiration Turbocharging with subsequent air cooling (by a cooling radiator) and Turbocharging with intercooler
      Manufacturer Volvo and John Deere
      Model D7E and 6-466A
      Cylinders number 6 and 6

      Hydraulic system

      Type of pump axial piston pump and Constant pressure system with locking in the middle position, with the piston pump of variable displacement volume

      Gear box

      Transmission type HTE 840, Sequential direct drive gearbox with shifting under load Volvo and powershift
      Forward gears number 8 and 8
      Reverse gears number 4 and 4

      Front Axle

      Wheel tilt 18 degrees and 20 degrees
      General fluctuations 16 degrees and 30 degrees

      Dump

      Left lateral displacement 673 mm and 683 mm
      Lateral right shift 673 mm and 683 mm
      Mouldboard width 3657.6 mm and 3657.6 mm
      Mouldboard height 635 mm and 609.6 mm
      Mouldboard thickness 22 mm and 22.4 mm

      Circle

      Diameter 1626 mm and 1500 mm
      Rotating 360 degrees and 360 degrees
      Left shift 775 mm and 851 mm
      Right shift 749 mm and 813 mm

      Images

      Sizes

      1. Dimensional length 9150 mm 1. Dimensional length 8470 mm
      2. Between tyres width 2537 mm 2. Between tyres width 2440 mm
      3. Height to cab upper part 3225 mm 3. Height to cab upper part 3200 mm
      4. Wheelbase 6280 mm 4. Wheelbase 5970 mm
      6. Front part clearance 610 mm 6. Front part clearance 572 mm
      8. Blade base 2650 mm 8. Blade base 2720 mm